What are the products used in water treatment and their characteristics?

Various sensors are used to measure temperature by sensing some change in physical properties. Whether you are measuring temperature in the laboratory or with a temperature measurement device in a rugged remote location, Banna has the right measurement device for your application. What are the products used by Banna in the United States for water treatment and their characteristics

Banna manufactures reliable and cost-effective sensors and water/sewage treatment switches or clean water supply systems to monitor water levels and flows and pressure. Typical applications include: Pumping station - running dry protection, level monitoring, pressure monitoring, flow monitoring Typical products include: Electromagnetic flowmeter FEM1000 Vortex flowmeter FVX100 Thermal flow switch Intelligent differential pressure transmitter P400 Radar level meter Liquid level transmission Let's take a closer look at the device L30M below. The operation of the electromagnetic flowmeter FEM1000FEM1000 is based on Faraday's law, which states that the voltage (E) induced by any conductor when moving at a right angle through a magnetic field (B) is related to the velocity of the conductor (V) proportional. Features 1. No moving parts - easy to maintain; no pressure drop since there are no blocked flowing parts. 2.DN10...DN20003. Suitable for corrosive media 4.Digital LCD for instantaneous/total flow display 5.Operating temperature: -20°C...180°C6.High reliability, direct output to PLC7.High Accuracy, anti-interference ability 8. No moving parts, long life II. FVM100 Series When a columnar object (the object that generates bortices) is placed in the flow path of the fluid, a rule called a Karman vortex channel is generated at the rear of the object vortex channel. Since the frequency of generated vortices is linearly proportional to the flow velocity over a given range, flow can be measured by counting the number of vortices. Typical applications: superheated steam, saturated steam and conventional fluid volume flow or weight flow measurement; cooling towers and condensate water; municipal water treatment and distribution; boiler feed water; chemical treatment; swimming pools and water parks Features 1. Pulse output frequency is proportional to the flow rate , no zero drift, and the performance is very stable. 2. High measurement accuracy: liquid content ≤ 0.0%; gas content 0.5%; 3. The sensing component has no contact with the medium - meaning high reliability, simple structure, easy installation, and low maintenance cost. 4. Suitable for liquid, gas, steam and some mixed liquid measurements 5. Wide measurement range 6. Liquid volume measurement does not require compensation; however, temperature and pressure compensation are necessary for steam weight flow and/or gas volume flow measurement. 7. Low pressure drop, energy-saving flow meter 8. Easy to install: vertical, horizontal or any angle pipe. 9. Within a given Reynolds number range, the frequency of the output signal has nothing to do with fluid density, viscosity or composition. Calibrated in one medium and used in other media. 10. Pulse or electrical output signals can be transmitted over long distances and the Hart protocol can be used. 3. FT20N series FT20N is based on two temperature sensors located within the medium. Not addedThermal sensors record liquid temperature. The other sensor is heated a few degrees above the medium, and when the medium flows, the heat generated in the sensor is conducted away by the medium. Measure the temperature of the sensor and compare it to the temperature of the medium. The flow state can be derived from the temperature difference. Typical applications: hydraulic and pneumatic systems, circulating water systems, pump dry run protection. Features 1. No moving parts - no maintenance required 2. Single model suitable for multiple pipe sizes 3. Compact design 4. Low pressure loss 5. LED displays flow trend and switch status 4. P400DP Intelligent Differential Pressure Transmitter P400 Series Differential Pressure Transmitters are designed to measure the pressure of liquids, gases or vapors. The complete sealed capacitive sensing element makes the device very stable and reliable with high measurement accuracy. Communicates with the control system or handheld communicator via the standard HART protocol, through which setup, configuration, monitoring and testing can be easily completed. Features: 1. High precision, high reliability and stability 2. Zero point and span programmable on site 3. Standard equipped HART protocol 4. Selectable wetted parts materials 5. Optional remote diaphragm sealing system 6. Adjustable damping 7. Optional explosion-proof model five. LR200 Series The operation of the FR100 involves sending the microwave beam emitted by the sensor to the surface of the medium in the tank. The electromagnetic waves that strike the fluid surface return to a sensor mounted on the top of the tank or container. The time it takes for the signal to return, known as time of flight (TOF), is then determined to measure the media level in the tank. Radar technology is used for level detection in continuous level measurement applications. Radar level detectors basically include: 1. A transmitter with a built-in solid-state oscillator. 2. Radar antenna. 3. Receiver as well as signal processor and operator interface.

American Banna provides a variety of flow measurement products: electromagnetic flowmeters, positive displacement flowmeters, paddle flow switches, piston flow switches, thermal flow switches (sensors), turbine flowmeters and vortex flowmeters.